| |
| |
DON 2.0 |
Gasket material with very good resistance to acids and alkaline media.
TESNIT® BA-C is specially developed soft gasketing material for the chemical industry. It is an sealing material based on aramide fibres and CSM rubber. The material has very good resistance to acids and alkaline media. It is also very covenient for the different aggressive media. TESNIT® BA-C finds the application in all places where the chemical resistance is the most demanding factor.
|
Gasket material for sealing of extremely aggressive media in many industries.
Basis | Aramide fibres, CSM |
Approvals |
Treatment with graphite, PTFE and antistick coating is available on request.
Sheet size | mm | 1000x1500, 1500x1500, 3000x1500, 4500x1500 |
Thickness | mm | 0.5, 0.8, 1.0, 1.5, 2.0, 3.0 |
other dimensions and thicknesses on request
Typical values for a thickness of 2 mm
Compressibility |
| % | 8 |
Recovery | ASTM F/36/J | % | 45 |
Tensile strength | DIN 52910 | N/mm2 | 10 |
Stress resistance | DIN 52913 | ||
16h, 300°C, 50N/mm2 | N/mm2 | ||
16h, 175°C, 50N/mm2 | N/mm2 | 25 | |
Specific Leak Rate | DIN 3535/6 | mg/sm | 0.06 |
Thickness increase | ASTM F 146 | ||
Oil IRM 903, 5h, 150°C | % | ||
ASTM Fuel B, 5h, 23°C | % | ||
HNO3 40%, 18h 23°C | % | 10 | |
H2SO4 65%, 48h, 23°C | % | 8 | |
Max. operating conditions | |||
Peak temperature | °C/F | 200/392 | |
Continuous temperature | °C/F | 150/302 | |
Pressure | bar/psi | 60/870 |
| General suitability using common installation practices under the condition of chemical compatibility. |
| Max. performance is ensured through appropriate measures for joint design and gasket installation. Consultation is recommended. |
| Limited application area - Technical consultation is mandatory. |
The Pressure - Temperature charts are the most current method of determining the suitability of a gasket material in a known application. Maximum figures for temperature and pressure can be misleading. Max. temperature and max. pressure represent maximum values and should not be used simultaneously. They are given only for guidance, since this max. values depend not only on the type of gasket material but also on the assembly conditions. Use the pressure and temperature graphs to check suitability of chosen gasket material for your application (combination of pressure and temperature).
 | Acetamide | | Ethane |  | Oleum | ||
| Acetic acid 10% |  | Ethyl acetate | | Oxalic acid | ||
| Acetic acid 100% | | Ethyl alcohol | | Oxygen | ||
| Acetic ester | | Ethyl chloride | | Palmitic acid | ||
| Acetone | | Ethylene | | Pentane | ||
| Acetylene | | Ethylene glycol | | Perchloroethylene | ||
| Adipic acid | | Formaldehyde | | Phenol | ||
| Air | | Formic acid 10% | | Phosphoric acid | ||
| Alum | | Formic acid 85% | | Potassium dichromate | ||
| Aluminium acetate | | Freon 12 | | Potassium acetate | ||
| Aluminium chlorate | | Freon 22 | | Potassium bicarbonate | ||
| Aluminium chloride | | Fuel oil | | Potassium carbonate | ||
| Ammonia | | Gasoline | | Potassium chloride | ||
| Ammonium bicarbonate | | Glycerin | | Potassium hydroxide | ||
| Ammonium chloride | | Heptane | | Potassium iodide | ||
| Ammonium hydroxide | | Hydraulic oil (Mineral) | | Potassium nitrate | ||
| Amyl acetate | | Hydraulic oil (type glycol) | | Potassium permanganate | ||
| Aniline | | Hydraulic oil (type phosphate esther) | | Propane | ||
| Asphalt | | Hydrazine | | Pyridine | ||
| Barium chloride | | Hydrochloric acid 20% | | Salicylic acid | ||
| Benzene | | Hydrochloric acid 36% | | Silicone oil | ||
| Benzoic acid | | Hydrofluoric acid 10% | | Soap | ||
| Blast furnace gas | | Hydrofluoric acid 40% | | Sodium aluminate | ||
| Borax | | Hydrogen | | Sodium bicarbonate | ||
| Boric acid | | Isobutane | | Sodium bisulphite | ||
| Butane | | Isopropyl alcohol | | Sodium carbonate | ||
| Butyl alcohol | | Kerosene | | Sodium chloride | ||
| Butyric acid | | Lead acetate | | Sodium cyanide | ||
| Calcium chloride | | Lead arsenate | | Sodium hydroxide | ||
| Calcium hydroxide | | Magnesium sulphate | | Sodium sulphate | ||
| Carbon bisulphide | | Malic acid | | Sodium sulphite | ||
| Carbon dioxide | | Methane | | Starch | ||
| Chlorine, dry | | Methanol | | Steam | ||
| Chlorine, wet | | Methyl chloride | | Stearic acid | ||
| Chloroform | | Methyl ethyl ketone | | Sugar | ||
| Chromic acid | | Methylene dichloride | | Sulfuric acid 20% | ||
| Citric acid | | Milk | | Sulfuric acid 96% | ||
| Copper acetate | | Mineral oil type ASTM 1 | | Tar | ||
| Creosote | | Naphtha | | Tartaric acid | ||
| Cresol | | Nitric acid 20% | | Toluene | ||
| Cyclohexanol | | Nitric acid 40% | | Transformer oil | ||
| Cyclohexanone | | Nitric acid 96% | | Trichloroethylene | ||
| Decalin | | Nitrobenzene | | Water | ||
| Dibenzylether | | Nitrogen | | White spirit | ||
| Dimethyl formamide | | Octane | | Xylene | ||
| Dowtherm | | Oleic acid |  |
|
totally satisfactory | |
doubtful | |
totally unsatisfactory |  |
no data - please contact our Technical service |
ASTM F 36/J
